sponsored
by

Vent roof in Building Supplies

sort by:
add tax & shipping for
 
 
 
store rating:
  • product
Roof Terminal For BGD90 Gas Fireplaces.For use with Napoleon Dream Direct Vent Fireplace, BGD90NT and BGD90PT.
 
  • product
Use A Listed Category III Vent Adapter To connect The Flue Collar To the Vent System. Use Category III Vent pipe For The Entire Length Of The exhaust pipe. Noritz N-Vent Is UL approved Category III Venting. N-Vent is Approved For Tankless And Boiler...
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  $22.25

 

  • product
  • coupons
The flat roof flashing is used to cover the hole in the roof used to pass the vent through to the outside. When used with a storm collar it diverts water away from the hole and prevents leakage in to the house or chase. 4 inch Pellet Vent is used in...
at

Rebates, Free Gift Cards with Purchase, Free Shipping and more at Home Depot

 
  • product
Use A Listed Category III Vent Adapter To connect The Flue Collar To the Vent System. Use Category III Vent pipe For The Entire Length Of The exhaust pipe. Noritz N-Vent Is UL approved Category III Venting. N-Vent is Approved For Tankless And Boiler...
 
store rating:
  $47.88

 

  • product
  • coupons
Designed as a replacement motor for our power roof vents. This unit is to be used with models PG1-2 and PR1-2.
at

Rebates, Free Gift Cards with Purchase, Free Shipping and more at Home Depot

 
store rating:
  • product
ProTech Systems FasNSeal FSVRJ3 3" Roof Jack (300911) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in...
 
store rating:
  • product
ProTech Systems FasNSeal FSVRJ4 4" Roof Jack (300912) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in...
 
store rating:
  • product
Z-Flex 2SVSADJF03 Z-VENT 3&quot Adjustable Roof Flashing
at
 
store rating:
  • product
Z-Flex 2SVSADJF04 Z-VENT 4&quot Adjustable Roof Flashing
at
 
  • product
Use A Listed Category III Vent Adapter To connect The Flue Collar To the Vent System. Use Category III Vent pipe For The Entire Length Of The exhaust pipe. Noritz N-Vent Is UL approved Category III Venting. N-Vent is Approved For Tankless And Boiler...
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
ProTech Systems FasNSeal FSVPF3 3" Variable Pitch Roof Flashing (8.7" height x 5.2" diameter) (300922) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired...
 
store rating:
  • product
ProTech Systems FasNSeal FSVPF4 4" Variable Pitch Roof Flashing (8.7" height x 6.2" diameter) (300923) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired...
 
store rating:
  • product
ProTech Systems FasNSeal FSVRJ5 5" Roof Jack (300913) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired appliances listed as Category II, III and IV or in...
 
store rating:
  • product
ProTech Systems FasNSeal FSVPF5 5" Variable Pitch Roof Flashing (8.7" height x 7.2" diameter) (300924) FasNSeal® is a Special Gas Vent and Gas Vent Connector, made from AL29-4C® stainless steel and designed for use on natural gas or propane-fired...
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
Z-Vent is a factory built, engineered AL29-4C special gas vent pipe, suitable for positive or negative pressure. Z-Vent is UL tested and listed to UL1738/S636. CAT II, III, IV venting approved. Flashing for use in flat roof or chimney application.
 
store rating:
  • product
Galvanized steel construction. Works with existing soffit intake vents to help remove damaging heat and moisture from the attic. More effective than roof louvers or turbine style vents. Helps prevent wood Rotating and extend the life of exterior paint....
 
store rating:
  • product
1 piece base and throat is weather tight and adds strength. Large flange for easy installation. NFA: 50 sq. in. per piece. 3 12 to 12 12 pitch. No. 85281: Gray aluminum No. 85282: Black aluminum No. 85283: Brown aluminum No. 85284: Weatherwood aluminum No
 
store rating:
  • product
40" aluminum or galvanized. Low profile, compact vent. Round throat, screened. NFA (sq. in.) 40 piece. 3 12 to 12 12 pitch. Aluminum: 12 pieces in a carton, galvanized: 9 pieces in a carton. No. RVA40000: Mill aluminum No. RVA40010: Black aluminum No. RVA
 
store rating:
  • product
1 piece base and throat is weather tight and adds strength. Large flange for easy installation. NFA: 50 sq. in. per piece. 3 12 to 12 12 pitch. No. 85281: Gray aluminum No. 85282: Black aluminum No. 85283: Brown aluminum No. 85284: Weatherwood aluminum No
 
store rating:
  • product
An asphalt based sealant specifically designed for sealing leaks and openings around chimneys, flashings, copings, roof decks, and roof vents. Roof repair withstands extreme temperature conditions and can even be applied in rain or snow. Dries to a...
 
store rating:
  • product
.021 nominal thickness. 16 oz. per sq. ft. Uses: Around chimneys, vent pipes, flues, as ridge cap under shingles, roof paper, or valley flashing. No. 67314: 14 x 10 No. 67514: 14 x 25
 
  • product
Four corner interior screws (not included) sandwich top metal base and inside garnish together to make a water-tight seal. Fits roofs 2 1/4" to 4 1/8" thick with standard 14" x 14" roof opening. UV-resistant, injection-molded plastic lid has unique...
 
  • product
Reflective cover helps prevent fading of interior and controls heat. Reflects UV rays. Installs over most standard 14" x 14" roof vents. Includes hook-and-loop tape for easy mounting. Cover is 16" x 16". Blocks heat and light from entering through your...
 
store rating:
  • product
1 piece base and throat is weather tight and adds strength. Large flange for easy installation. NFA: 50 sq. in. per piece. 3 12 to 12 12 pitch. No. 85281: Gray aluminum No. 85282: Black aluminum No. 85283: Brown aluminum No. 85284: Weatherwood aluminum No
 
store rating:
  • product
1 piece base and throat is weather tight and adds strength. Large flange for easy installation. NFA: 50 sq. in. per piece. 3 12 to 12 12 pitch. No. 85281: Gray aluminum No. 85282: Black aluminum No. 85283: Brown aluminum No. 85284: Weatherwood aluminum No
 
store rating:
  • product
DURAVENT" PELLET STOVE VENT ROOF FLASHING Use with 3" pellet pipe Adjustable For 0/12 to 6/12 pitch Double wall/insulated design .012" 430 stainless steel inner wall .018" galvalume steel outer wall 1" clearance to combustibles twist-lock construction...
 
store rating:
  • product
BLACK JACK WET/DRY FIBERED PLASTIC ROOF CEMENT - For roof repairs & stopping leaks ~ Use around vent pipes & flashings ~ Use around guttering & chimneys ~ Resistant to temperature changes ~ Forms a tight and shiny seal ~ Stays soft and pliable -...
 
store rating:
  • product
19" x 3", Low Profile Roof Dormer, The 1 Piece Base Eliminates Soldering, Screened With 1/4" Galvanized Wire Mesh, Has Extra Long Flashing Under Opening, Net Free Vent Area 37 SQIN, Blends With Any Architecture, Especially Popular In Northern & Central...
 
store rating:
  • product
Provides weather sealings for pipes and vents protruding through roofs. Black Swan's Thermoplastic Roof Flashing is an injection molded polypropylene base with 14 melt flow and 11 notched Izod for superior impact resistance. Thermoplastic base meets...
 
store rating:
  • product
Provides weather sealings for pipes and vents protruding through roofs. Black Swan's Thermoplastic Roof Flashing is an injection molded polypropylene base with 14 melt flow and 11 notched Izod for superior impact resistance. Thermoplastic base meets...
 
store rating:
  • product
BLACK JACK WET/DRY FIBERED PLASTIC ROOF CEMENT - For roof repairs & stopping leaks ~ Use around vent pipes & flashings ~ Use around guttering & chimneys ~ Resistant to temperature changes ~ Forms a tight and shiny seal ~ Stays soft and pliable -...
 
store rating:
  • product
19" x 3", Low Profile Roof Dormer, The 1 Piece Base Eliminates Soldering, Screened With 1/4" Galvanized Wire Mesh, Has Extra Long Flashing Under Opening, Net Free Vent Area 37 SQIN, Blends With Any Architecture, Especially Popular In Northern & Central...
 
store rating:
  • product
Broan Roof Cap 611 Roof Cap Vent Caps Roof Cap Fits Duct Size 8 In Cap Height 9 7/8 In Cap Width 11 7/8 In Construction Material Aluminum For Us
 
store rating:
  • product
This solar ventilator removes hot humid air from roof spaces much more efficiantly than normal wind turbines Simple instructions show you how to cut a 3 inch hole or drill a pattern of small holes in your structure. The solar vent comes with a mounting...
 
store rating:
  • product
Provides weather sealings for pipes and vents protruding through roofs. Black Swan's Thermoplastic Roof Flashing is an injection molded polypropylene base with 14 melt flow and 11 notched Izod for superior impact resistance. Thermoplastic base meets...
 
store rating:
  • product
16 attic air exchanges per hour. 1300 CFM for attics up to 2,600 sq. ft. 14" blade diameter. Rust resistant metal construction. Flashing size 21" x 22-1/4".
 
store rating:
  • product
Air Vent Automatic Power Attic Roof Ventilator 53860 Attic Ventilator Attic Ventilators Automatic Power Attic Roof Ventilator 120 Volts 1/6 HP 4.3
 
store rating:
  • product
PRV-50, Gray, Plastic Roof Vent, 40 SQIN Net Free Area, 16" x 20" Base Plate.
 
store rating:
  • product
Low Profile, Brown, Aluminum, Slant Roof Vent, 40 SQIN Net Free Area, 14" x 16-3/4" Base, 8" Opening Size, 8" x 8" Aluminum Screen, 1 Piece Dome & 1 Piece Base For Added Strength, Excellent For Small Spaces Where Ventilation Is Needed, Saves Energy,...
 
store rating:
  • product
Mill Finish Aluminum, Slant Back Roof Vent, Flashing Dimensions 16-3/4" x 18-3/4", 9-1/2" Opening Fits Between 16" On Center Rafters, 50 SQIN Net Free Area, 8"x8" Aluminum Screen, Will Ventilate 94 SQFT, Louvered On 3 Sides For Maximum Air Flow, Fits...
 
store rating:
  • product
8", Black, Galvanized, Slant Back Roof Vent, 40 SQIN Net Free Area, 14" x 16-3/4" Base, 1 Piece Dome & 1 Piece Base For Added Strength, For Small Spaces Where Ventilation Is Needed, Saves Energy, Reduces Moisture Damage.
 
store rating:
  • product
PELLET VENT ADJUSTABLE ROOF FLASHING #3VP-AF 3" Used to provide a transistion at the roof through which the vent will pass and protect the interior of the structure from weather Designed for use on roofs having slope of 0/12 (flat) to 6/12 Flashing...
 
store rating:
  • product
Universal Design This non-handed Awning Window or Roof Vent Operator has a diecast housing and a zinc plated, 4 inch (101.6 millimeter) arm. Minimum Order: 1 Package One operator with handle per package.