sponsored
by

Pioneer car amplifiers Car Amplifiers

Advertisement

you're in Car Amplifiers, see other matches in:

Advertisement
sort by:
add tax & shipping for
 
 
 

starting at

$185
  • product
mono subwoofer car amplifier * 300 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms) * variable low-pass filter (40-240 Hz) * wired bass control (variable 0 to 12 dB boost at 50 Hz) * preamp- and speaker-level inputs *

starting at

$185
 

starting at

$20
  • product
Rock out while youre on the road with this 4-channel amplifier that is ideal for use with a Pioneer AVIC-F500BT portable GPS receiver. Simply connect this amplifier to your Pioneer GPS receiver and enjoy your favorite tunes no matter where the road takes you.

starting at

$20
 

starting at

$129
  • product
4-Channel Bridgeable Amp (760W Max) 150 watts RMS x 2 bridged,4-channel selectable high- and low-pass filters,preamp- and speaker-level inputs

starting at

$129
 

starting at

$99
  • product
2-Channel Bridgeable Amp (600W Max) 380 watts RMS x 1 bridged,selectable low-pass filter,preamp- and speaker-level inputs

starting at

$99
 

starting at

$295
  • product
Pioneer PRS Series 4-Channel Full-Range FD Car Amplifier - PRSD4200F. Class-FD ICEpower Amplifier. Superior Channel Separation. Energy Saving Design. Speaker Level Inputs. Leads For Wiring Not Included. Black Finish

starting at

$295
 

starting at

$389
  • product
To experience the real sound effect you can install the Pioneer Premier PRS-D1200SPL Monoblock Amplifier that comes with a class-D microprocessor. This amplifier features signal-to-noise ratio greater than 105dB for optimal audio clarity. By using the Pioneer Premier Amplifier you can reduce signal distortion up to 0.01% THD. The Pioneer PRS-D1200SPL Subwoofer Amplifier with MOSFET power input delivers maximum 2400 watts Instant Maxx power output for expanded functionality. Integrating subsonic filters the system easily removes power-robbing frequencies below the tuning of the subwoofer or enclosure. With the help of Multiple Amplifier Synchronization System (MASS) you can connect nearly four SPL amplifiers to this unit.

starting at

$389
 

starting at

$122
  • product
The superior efficiency of a Class-D amplifier means higher power output and greater compactness than an analog amplifier offers.Class-D amplifiers overcome the inefficiencies of traditional Class-A or AB amplifiers. Pioneer's Class-D amps transform very little power into heat so a higher percentage of the power supply (67 %) is transformed into the load. This results in a very compact amp which needs less input power to produce very high output power. The Class-D amplifier's PWM (Pulse Width Modulator) modulates the original audio input signal with a triangulated signal wave which has a much higher fixed frequency. The result is a digital signal which contains both the input signal and a band of frequency components around the modulation frequency. A LPF (Low Pass Filter) then filters out the high frequency pulses and the resulting amplified output signal is then sent to the subwoofer and/or speakers.Bass boost gives you more control over how your music sounds. It lets you set the optimal bass level for each speaker/sub connected to the GM-D7400M, so the tone controls from your headunit can do what they do best. And because this is selectable bass boost, you can set the level at 0dB, 6dB, or 12dB, whichever sounds best to you.Built into the GM-D7400M is a very smart crossover network. It works like a gateway, routing the big bass signals (adjustable from 40 to 240Hz or lower, at -12dB/octave) and filtering out higher-frequency signals to that subwoofer. This optimizes your system's efficiency and delivers the best possible sound quality.The GM-D7400M's speaker level inputs allow you to connect your OEM unit (or any unit that doesn't have the typical RCA-type inputs) without having to buy add-on adapters. So, the install goes faster, you save money, and you've got a Pioneer amp in your vehicle.

starting at

$122
 

starting at

$535
  • product
2000 watts RMS x 1 at 1-ohm 1,500 watts RMS x 1 at 2 ohms,variable low-pass filter (40-240 Hz, 24 dB per octave),selectable bass boost (0, 6, 9, 12 dB, variable from 40 to 120 Hz)

starting at

$535
 

starting at

$260
  • product
Pioneer Premier PRS Mono Class D Amplifier - PRSD1200M. 1200 Watts Peak Music Power. Full Custom-Made Power Supply Capacitor Bank. Linear Technology Operational Amplifier. Externally Bridgeable. Multi-Amplifier Synchronization System (MASS). Variable Crossover (40'240Hz, LPF). Selectable Bass Boost With Wired Bass Remote. Speaker Level Inputs

starting at

$260
 
  • product
Same Powerful Output from a More Compact Amp: 100 % of the power, 45 % of the size The superior efficiency of a Class-D amplifier means higher power output and greater compactness than an analog amplifier offers. Efficiently Compact, Awesome Power...
 

starting at

$140
  • product
A really good amp doesn't just provide power. It also offers options for customizing the sound in your vehicle. The 2-channel GM-5300T provides a selectable 50Hz bass boost and a built-in crossover for fine-tuning your tunes. Plus, it comes with speaker level inputs for easy connection to an OEM head-unit.Bass boost gives you more control over how your music sounds. It lets you set the optimal bass level for each speaker/sub connected to the GM-5300T, so the tone controls from your head-unit can do what they do best. And because this is selectable bass boost, you can set the level at 0dB, 6dB, or 12dB, whichever sounds best to you.Built into the GM-5300T is a very smart crossover network. It works like a gateway, routing the big bass signals (80Hz or lower, at -12dB/octave) to the speaker that handles them best, filtering out higher-frequency signals to that speaker. This optimizes your system's efficiency and delivers the best possible sound quality.The GM-5300T's speaker level inputs allow you to connect your OEM unit (or any unit that doesn't have the typical RCA-type inputs) without having to buy add-on adapters. So, the install goes faster, you save money, and you've got a Pioneer amp in your vehicle.

starting at

$140
 
store rating:
  • product
Amplifiers: 4 ohms: 125 watts x 2 chan. 2 ohms: 190 watts x 2 chan. Bridged, 4 ohms: 380 watts x 1 chan Max power output: 760 watts x 1 chan MOSFET power supply Selectable bass boost (0, 6, 12 dB at 50 Hz) Hi-volt input level control (400mV ~ 6.5V) 2/1...
 
store rating:
  • product
760 watts maximum power; 2 channelsLoad impedance capability 2-8 Ohm (stereo), 4-8 Ohm (bridged) Signal-to-noise ratio >95dB Bridgeable RCA inputs 2 channel; Speaker level input 2 channel Input level control hi-volt (400mV - 6.
 
store rating:
  • product
600 watts maximum power; 4 channels Load impedance capability 2-8 Ohm (stereo), 4-8 Ohm (bridged) Signal-to-noise ratio >95dB Bridgeable 4/3/2 channel capability RCA inputs 4 channel; Speaker level input (front/rear independent)4 channel Input level...
 
store rating:
  • product
Is your system showing it's full potential Amplifiers send a cleaner current to your car speakers. The 2-channel GM-5400T provides a selectable 50 Hz bass boost and a built-in crossover for fine-tuning your tunes. Plus, it comes with speaker level...
 
store rating:
  • product
Is your system showing it's full potential Amplifiers send a cleaner current to your car speakers. The 4-channel GM-6400F delivers up to 600 watts max power - plenty of juice to power your high-quality speakers.
 
store rating:
  • product
Amplifiers: 600 Watts Continuous Power Variable Crossover (40~240Hz, LPF) Selectable Bass Boost with Wired Bass Remote 600 Watts x 1, at 2 ohms <= 1
 

starting at

$141
  • product
The 4-channel GM-6300F delivers up to 600-Watts (60 watts x 4 or 150 watts x 2 at 4 ohms; 75 watts x 4 at 2 ohms) to power your high-quality speakers. It also has built-in 4-channel crossovers. Speaker level inputs allow for easy connection to head unit. Not only will your music be louder, it'll also be cleaner, getting the most out of your speakers and your music. Constant road noise makes it hard for the music to be heard clearly. But with up to 600-Watts of max power, you get to hear every word and note. Load Impedance Capability - 2-8 Ohm Stereo, 4-8 Ohm (Bridged) Frequency Response - 10Hz - 50kHz Total Harmonic Distortion - 0.010% PWM Regulated MOSFET Power Supply Screw-Type - Speaker Terminals Balanced Isolator Input Circuit Input Level Control Hi-Volt (400mV - 6.5v) Built-in Crossover LPF/HPF (Front/Rear Independent) Crossover Frequency Range - 80Hz, -12dB/Oct. Dimensions - 11-13/16 x 2-3/8 x 13-1/8 (300 mm x 60 mm x 334 mm) Professional installation required

starting at

$141
 
  • product
The goal of a good amplifier is to cleanly amplify the music signal, free of distortion or added color. The Premier PRS-D2000T is a new generation of Class FD (Full-Range Class D) amplifiers that clearly achieves this goal. Using an exclusive designed ICEpower circuit, music comes through clear, crisp and detailed.A huge benefit is the Class FD design, which consumes far less current than traditional amplifier designs. These results in less draw on your vehicle's alternator, and could actually improve fuel mileage in many cases. It also allows for a compact chassis (heat sink) that takes up less space and provides more installation flexibility.For added flexibility, the variable crossover lets you optimize your system's efficiency and delivers the best possible sound quality. You can adjust it continuously between 40 to 120Hz, as well as selecting from either High-Pass Filter (use for your main speakers) or Low-Pass Filter (use for your subwoofers), giving you the ultimate flexibility in setting up your system.The subsonic filter lets you remove power-robbing frequencies below the tuning of your subwoofer/enclosure. The subsonic is set at 20Hz with a steep 18dB/Octave roll off for optimal effect.What, you don't own a Pioneer head unit? The PRS-D2000T's speaker level inputs allow you to connect your OEM unit (or any unit that doesn't have the typical RCA-type inputs) without having to buy add-on adapters.
 
  • product
The Pioneer Premier PRS-D2100T 2-Channel Amplifier comes with a full-range class-D microprocessor with ICEpower circuit that delivers superior quality music. This cost-effective amplifier consumes less power thereby improving fuel mileage. With MOSFET power input and a maximum of 600 watts power output the Pioneer Premier PRS-D2100T D Class Amplifier offers good surround sound performance. This amplifier provides configurable bass effect of up to 12 dB at 45 Hz for optimal sound clarity. The gold-plated RCA input connectors protect the unit from corrosion and offer long lasting performance. You can get instant alerts on low and high voltage and other electrical instabilities with the help of the LED power indicator.
 
  • product
Peak Watts: 120 x 4 - Bridged Watts: 150 x 2 - With Built-in Crossover - 100 db Signal to Noise Ratio
 
  • product
Peak Watts: 380 x 2 - Bridged Watts: 380 x 1 - With Built-in Crossover - With Bass Boost - 100 db Signal to Noise Ratio
 
  • product
Peak Watts: 800 x 1 - With Built-in Crossover - With Bass Boost - 100 db, 80 db Signal to Noise Ratio
 
  • product
Continuous Power (14.4V): 50Wx2 (4ohm), 75Wx2 (2ohm), 150Wx1 (4ohm)
 
  • product
Continuous Power (20Hz-20kHz, 0.08% THD): 4 ch: (4 Ohm) 30Wx4 - 4 ch: (2 Ohm) 35Wx4 - 2 ch: (4 Ohm) 70Wx2
 
  • product
Continuous Power (14.4V): 125Wx2 (4 ohm), 190Wx2 (2 ohm), 380Wx1 (4 ohm)
 
  • product
Continuous Power (20Hz-20kHz, 0.04% THD) * 2 ch: (4 Ohm) 50Wx2 * 2 ch: (2 Ohm) 75Wx2 * 1 ch: (4 Ohm) 150Wx1
 
  • product
Continuous Power (14.4V): 40Wx2 (4ohm), 50Wx2 (2ohm), 100Wx1 (4ohm)
 
  • product
The 4-channel GM-6000F delivers impressive peak music power at 480 watts, and its pulse width modulation (PWM) circuit efficiently outputs only the lower frequencies—perfect for powering subs. You can configure your system with 50 watts into 4 channels at 4 ohms, 60 watts into 4 at 2 ohms, or use bridged power with 120 watts x 2 into 4 ohms. The variable high-pass and low-pass filters make it easy to upgrade your music system, and oversized screw-type power/ground terminals and RCA in/outputs are provided
 
  • product
760W of peak music power does tend to get people’s attention. The beefy GM-5000T amp offers 1-, 2-, and 3-channel operation (including a bridged 380W x 1 into 4 ohms, continuous), plus a Hi-Volt Input Level Control (200mV-6.5V) and a Selectable Low-Pass Filter for added control and flexibility. It features a Pulse Width Modulation (PWM) circuit that efficiently outputs only the lower frequencies, which makes it ideal for powering subs. Oversized screw-type power/ground terminals and RCA inputs are provided
 
  • product
The super-efficient GM-4000F amplifier dishes out 300 watts of peak music power and can be configured for 2-, 3-, or 4-channel operation. Its pulse width modulation (PWM) circuit efficiently outputs only the lower frequencies, which makes it ideal for powering a sub or two. The selectable high-pass and low-pass filters give you flexibility for your system, and the 4-channel speaker level input offers added control. Oversized screw-type power/ground terminals and RCA in/outputs are provided.
 
  • product
Big sound, small package: only 6-1/8” wide, the compact GM-3000T offers 1-, 2-, and 3-channel operation (including a bridged 100W x 1 into 4 ohms), plus a Hi-Volt Input Level Control (400mV ~ 6.5V) and a Selectable Low-Pass Filter for added control and flexibility. It features a pulse width modulation (PWM) circuit that efficiently outputs only the lower frequencies — perfect for powering a sub. Oversized screw-type power/ground terminals and RCA inputs are provided, and the 2-channel speaker level input offers added control
 
  • product
All-Powerful: The explosive GM-D510M Class D amplifier delivers massive power with less heat—and less distortion—than a conventional amp. Its pulse width modulation (PWM) circuit efficiently outputs only the lower frequencies, perfect for powering that monster sub. And all this power—a thunderous 1000 watts (max) into 2 ohms, or 600 into 4—comes in a small chassis, saving space for your install. The GM-D510M includes a MOSFET output section, screw-type speaker terminals, and oversized power/ground terminals. Plus, its built-in variable crossover (40~240Hz with -24dB/Octave slope) allows you to dial in your settings for maximum performance
 
  • product
Continuous Power (20Hz-20kHz, 0.04% THD): 2 ch: (4 Ohm) 50Wx2 - 2 ch: (2 Ohm) 100Wx2 - 1 ch: (4 Ohm) 200Wx1
 
  • product
Description: This new amplifier is designed to combine high power output and high efficiency while s
 
  • product
Description: This new amplifier is designed to combine high power output and high efficiency while s
 
  • product
2 channels 125W x 2 @ 4 190W x 2 @ 2 Selectable low-pass crossover Bass boost Speaker level i
 
  • product
4 channels 60W x 4 @ 4 75W x 4 @ 2 Selectable 4-channel crossovers Speaker level inputs
 
  • product
Continuous Power (20Hz-20kHz, 0.08% THD): 2 ch: (4 Ohm) 35Wx2 - 2 ch: (2 Ohm) 50Wx2 - 1 ch: (4 Ohm) 80Wx1
 
  • product
The 4-channel GM-X374 features Pioneer's PWM-regulated MOSFET power supply and DMOSFET output circuitry for 400 Watts (max.) of big, efficient power with low distortion. A bridgeable 2/3/4-channel capability gives you system flexibility, and a built-in selectable crossover makes your install much easier. Speaker level inputs (4-channel) provide added control, and the "New Retro" aluminum vertical heat sink and high-volt (200mV-6.5V) input level control both improve performance. RCA inputs (4-channel) and outputs (pass-through) are included
 
  • product
Big, efficient power: the GM-D500M is a Class D amplifier, so you get massive power with less heat - and less distortion - than with a conventional amp. Its pulse width modulation (PWM) circuit efficiently outputs only the lower frequencies, so it's perfect for powering subs. More good news: all this power comes in a small chassis, saving space for your install. It includes a MOSFET output section, screw-type speaker terminals and oversized power/ground terminals, and a die-cast aluminum heat sink. Plus, the built-in variable crossover cuts down on install time
 
  • product
Continuous Power (14.4V): 65Wx2 (4 ohm), 75Wx2 (2 ohm), 150Wx1 (4 ohm)
 
  • product
Continuous Power (14.4V): 50Wx4 (4 ohm), 60Wx4 (2 ohm), 120Wx2 (4 ohm)
Best prices on Pioneer car amplifiers in Car Amplifiers. Check out BizRate for great deals on Car Amplifiers from Pioneer. Use BizRate's latest online shopping features to compare prices for Pioneer car amplifiers. Read product specifications, calculate tax and shipping charges, sort your results, and buy Electronics with confidence. Easily narrow your search and find the product that's perfect for you: Pioneer GM-D8400M Monoblock Class D Car Amplifier - Pioneer ND-G500 4-Channel Gateway Audio Integration Amplifier.