Humminbird parts Marine Electronics

Description:

Plastic - Through Hull

Description:

Transom Mount Transducers Transom Transducers mount on the transom (back) of the boat in contact with the surface of the water. To prevent damage to the boat or transducer. Transom mount hardware is included with the transducer. Description: New transom mount transducer design. Single/Dual Beam, 20/60 Degree, 200/83 kHz with built in temperature sensor. New design is more secure and is not a prone to kick up at high force of waves. It has an improved running angle and a optional lock down screw to override the kick up. Has same hole pattern as some older version transducers For Use With: Matrix 10, 12, 15, 17, 20, 27, 67, 77c, 87c, 97, 717, 727, 737, 767, 777, 787, 323, 343, 363, 383, 141, 161, PMax10, PMax15, PMax20, PMax210, PMax215, PMax220, 917c, 931c, 937c, 957c, 997c, 515, 525, 535, 565,580, 585c, 595c, Piranha 2, Piranha 4, XP2000, XP4000

Description:

PRODUCT FEATURES:Temperature range of 25-99.9 degrees FSpeed range of 2-75 MPHTemp Speed Sensor, 20 ft. cable.

Description:

Transducer Switch Transducer Switch connects two transducers to one fishfinder Description: Transducer Switch which allows you to use two transducers on one depth sounder For Use With: All Matrix (except Matrix 47 3D), 700 Series, 500 Series, 300 Series, 100 Series, 900 Series (except 947c and 967c), Wide Series (except One, 100, 128, 3D View, 3D Vision, 3D Vista) 300TX, 400TX, all Piranha, all PiranhaMax and HDR610

Description:

Speed Sensor Temperature and Speed Sensors are an optional accessory for many Humminbird fishfinders. The sensors provide quick response to changes, and readout from 2 to 70 MPH for speed, and from 25 degrees to 99 degrees for temperature. Description: Speed Sensor, 20 ft cable, transom mount. Speed range of 2-75 MPH. For Use With: Matrix 10, Matrix 10 Portable, Matrix 10 Track Pack, Matrix 15, Matrix 15 Plus, Matrix 17, Matrix 20, Matrix 20 Portable, Matrix 20 Track Pack, Matrix 25, Matrix 25 Plus, Matrix 27, Matrix 35, Matrix 35 Plus, Matrix 37, Matrix 55, Matrix 65, Matrix 67, Matrix 97, Fishfinder 515, Fishfinder 535, Fishfinder 565, Matrix 47 3D, Matrix 77C, Matrix 87C, FF585C, FF595C, 931C, 937C, 947C, 981C, 987C.

Description:

Power Cable Power Cable replacements for all Humminbird fishfinders, radios, and GPS equipment have a connector at one end and soldered bare leads for connection to the power source at the other. Power connection should be made to the boats fuse panel or through an inline fuse holder (not included on most cables) if made directly to the battery. Description: Power cable, 6 ft, waterproof. Used with all Humminbird products produced since 1989 For Use With: TCR-ID-1, TCR-101, TCR-ID-10, PLATINUM ID 120, PLATINUM ID 600, LCR400, LCR400 ID, DIM 3-120, DIM 3-600, LCR 100G, WIDE ONE, WIDE EYE, WIDE VIEW, WIDE VISION, WIDE 3D VIEW, WIDE 3D VISION, WIDE 3D VISTA, WIDE 100, WIDE 128, WIDE OPTIC, WIDE PORTRAIT, WIDE PANORAMA, WIDE PARAMOUNT, WIDE 3D PARAMOUNT, WIDE W, PRO FLASHER, LCR 120, OEM-LCR, LCR-3D, HBL201G, SR-ID 600, ULTIMA, 100SX, 200DX, 300TX, 400TX, PRO ANGLER, TOUR SERIES, PRO ANGLER 160, XTREME 160, TRACKER 160, TRAK PRO 128, 105SX, 405SX, ALL PIRANHA PRODUCTS, LEGEND 1000, LEGEND 1000 DEEP, LEGEND 2000, LEGEND 2000 DEEP, LEGEND 3000, LEGEND 3000 DEEP, ALL MATRIX ALL PIRANHA PRODUCTS, ALL FISHFINDER 300 SERIES, ALL 500 SERIES, ALL 700 SERIES, ALL 900 SERIES.

Description:

Transom Mount Transducer Transom Transducers mount on the transom (back) of the boat in contact with the surface of the water. To prevent damage to the boat or transducer. Transom mount hardware is included with the transducer. Description: High-speed transom mount transducer, 200 kHz, 20 ft cable, modular connector, 24 degree cone angle, high speed hardware. For Use With: WIDE 100, WIDE 128, 100SX, 105SX, 405SX, 405SX Plus, Pro Angler 400SX

Description:

Transom Mount Transducer Transom Transducers mount on the transom (back) of the boat in contact with the surface of the water. To prevent damage to the boat or transducer. Transom mount hardware is included with the transducer. Description: Transom mount transducer, wide side 3 element, 20 ft. cable. Allows the unit to look left, right, or down. Not recommended for high-speed use. For Use With: WIDE EYE, WIDE VIEW, WIDE VISION, WIDE OPTIC, WIDE PORTRAIT, WIDE PANORAMA, WIDE PARAMOUNT, 300TX, 400TX, MATRIX 37, MATRIX 67, MATRIX 97.

Description:

Description:

Transom Mount Transducer Transom Transducers mount on the transom (back) of the boat in contact with the surface of the water. To prevent damage to the boat or transducer. Transom mount hardware is included with the transducer. Description: New transom mount transducer design. Quadra Beam, 20/60/90 Degree, 200/83/455 kHz with built in temperature. New design is more secure and is not a prone to kick up at high force of waves. It has an improved running angle and a optional lock down screw to override the kick up. Has same hole pattern as some older version transducers For Use With: 300TX, 400TX, Wide Optic, Wide Portrait, Wide Panorama, Wide Paramount, FF575, Matrix 37, Matrix67, Matrix 87c. Matrix 97, 737, 767, 787c, 787c2i, 917c, 957c, 997c, PiranhaMax 240

Description:

The Humminbird DBK2 Marine Electronics Transducer with a built-in XTM 9 20 T dual beam has a coverage area of 2060 degrees at 20083 kHz frequency. To provide optimal protection from entanglement you can mount this dual beam transducer on your trolling motor easily. The Humminbird DBK2 Transducer is compatible with the Matrix 10 12 87c and 97 Piranha 2 and 4. It can also be used along with XP2000 and XP4000 all 300 and 100 series fish finders. Featuring a power cable and a product manual the Humminbird DBK2 Transducer provides ease of usage and maintenance. The Humminbird DBK2 Second Station Kit comes with a quick disconnect mounting system offering fast installation and removal.

Description:

P/N: 710205-1 - Trolling Motor

Description:

The Humminbird STH 7W Bronze Thru-Hull Transducer is for large boats, and boats with in-board motors that make most typical transducers ineffective. This bronze thru-hull transducer is not recommended for trailered boats, and Humminbird recommends you have it professionally installed due to the fact that it requires a hole be drilled in the hull and the shaping of a fairing block. The STH 7W is a six-beam transducer with a 53-degree beam angle and an operating frequency of 455 kHz that is intended for 3D sonar applications only. This unit is 4.25 inches in diameter, with a 1.25-inch below-hull depth and a shaft diameter of 0.81 inches. The Humminbird STH 7W comes with a 30-foot connecting cable and all the necessary mounting hardware, but does not include a fairing block. Scheduled for release sometime in April of 2007, the STH 7W is compatible with Humminbird's; Matrix 47 3D, 947C 3D, Wide 3D Vision, Wide 3D Vista, and Wide 3D Paramount sonar systems. This item is backed by Humminbird's one-year limited warranty.

Description:

Humminbird 755C ChartplotterThe 755c Chartplotter has what you are looking for with a full 320V x 240H color TFT screen for clear views of the charts, navigation info, depth contours and more.Features:Additional Features:Included Accessories/Parts:

Description:

Mounting High Speed Transducers to the Transom - Includes Plastic Bracket with Plastic Pivot

Description:

Humminbird XNT 9 SI 180 T New transom mount transducer design. Compact dual/side imaging. 20/74/84 degree, 200/83/455 kHz with built in temperature. New design is more secure and is not a prone to kick up at high force of waves. It has an improved running angle and a optional lock down screw to override the kick up. Has same hole pattern as some older version transducers For Use With: 797c

Description:

The Humminbird XHS 9 SI 160 T Transom Mount Transducer is a transducer designed to mount on the transom, or back, of the boat, in contact with the surface of the water, and operate in conjunction with a compatible Humminbird sonar or fish finder system. This unit is a side-imaging transducer with operating frequencies of 262, 200 and 50 kHz for a 160-degree total beam width, and a built-in temperature probe. The XHS 9 SI 160 T features a 20-foot cable, and all the necessary hardware to get up and running right away. The Humminbird XHS 9 SI 160 T transducer is specifically designed for use with Humminbird's 981C SI and 987C SI only. This item is backed by Humminbird's one-year limited warranty.

Description:

Bronze - Thru Hull

Description:

Description:

The Humminbird SHS 7W Transom Mount Transducer places the transducer on the outside of the boat hull, which produces the least signal loss and provides a way to adjust the transducer after installation. The mounting hardware included is designed to protect both the boat and the transducer should the boat strike debris in the water or when trailering. The SHS operates on the 455 kHz frequency, and includes a 20-foot cable, six elements, and a seven-pin connector. This unit is designed for use with Humminbird's Wide series of fishfinders.

Description:

Description:

Description:

Portable Mounting Hardware Portable Mounting Hardware is hardware and a suction cup for mounting Portable Transducers. Description: Mounting hardware and suction cup for portable transducers. For Use With: 200DX, 300TX, 400TX, Wide Panorama, Wide Paramount, FF515, FF535, FF565, PiranhaMax 10, PiranhaMax 15, PiranhaMax 20

Description:

Size: 20 Ft

Description:

Transducer Extension Cable The Transducer Extension Cables extend the location of transducers up to 50 feet without affecting accuracy or performance. All cable end connectors are gold plated for corrosion resistance. Description: Transducer Extension Cable, 10 ft, modular connector. For Use With: TCR-101, TCR-ID-1, TCR-ID-10, PLAT ID 120, PLAT ID 600, LCR400, LCR400 ID, HDR 200I, HDR 600I, WIDE ONE, WIDE ONE-D, WIDE 100, NS10-US, NS25, ULTIMA, HBL 201G, SR-ID 600, OEM-LCR, LCR 120, LCR100s, WIDE W, LCR W, TRACKER 160, PRO ANGLER 160, XTREME 160, PRO ANGLER 400SX, TRAK PRO 128, WP60 ID, 100SX, 200DX, WIDE 2000, z160, 105SX, 405SX, LEGEND 1000, LEGEND 1000 DEEP, LEGEND 2000, LEGEND 2000 DEEP, LEGEND 3000 DEEP. Also works with the 200 kHz transducer (XHS-6-16) for the WIDE 3D VIEW, WIDE 3D VISTA, 3D PARAMOUNT.

Description:

Size: 5.7 x 4.1 x 2.7 in.

Description:

Description:

Transducer Extension Cable, 10ft. The Transducer Extension Cables extend the location of transducers up to 50 feet without affecting accuracy or performance. All cable end connectors are gold plated for corrosion resistance. For Use With: 300TX, 400TX, Tour Series, Wide Eye, Wide View, Wide Vision, Wide 3D View, Wide 3D Vision, Wide 3D Vista, Wide Optic, Wide Portrait, Wide Panorama, Wide Paramount, Wide 3D Paramount, Matrix 10, Matrix 15, Matrix 17, Matrix 20, Matrix 25, Matrix 27, Matrix 35, Matrix 37, Matrix 55, Matrix 65, Matrix 67, Matrix 97, FF515, FF535, FF565, FF585c, FF595c, Piranha 1, Piranha 2, Piranha 3, Piranha 4, Piranha 5, PiranhaMax 10, PiranhaMax 15, PiranhaMax 20, 323, 343c, 363, 383c, 727, 737, 767, 777c, 777c2, 787c, 787c2.

Description:

Length: 30 Ft.

Description:

Temp/Speed Extension Cable The Temperature and Speed Extension Cables extend the location of Temp/Speed sensors up to 50 feet without affecting accuracy or performance. All cable end connectors are gold plated for corrosion resistance. Description: Temp/Speed extension cable, 10 ft. For Use With: WIDE EYE, WIDE VIEW, WIDE VISION, WIDE 3D VIEW, WIDE 3D VISION, WIDE 3D VISTA, WIDE OPTIC, WIDE PORTRAIT, WIDE PANORAMA, WIDE PARAMOUNT, WIDE 3D PARAMOUNT, WIDE 2000, WIDE W, LCR W, TOUR SERIES, 200DX, 300TX, 400TX, ALL MATRIX PRODUCTS, ALL 500 SERIES, ALL 300 SERIES, ALL 700 SERIES, ALL 900 SERIES.