Transition networks Networking Products

Description:

Convert 1000BASE-T ports over to 1000BASE-SX/LX on a port-by-port basis. Used individually or in pairs, this media converter can extend Gigabit Ethernet up to 2 km over multimode fiber or up to 65 km over single mode fiber.

Description:

With: BNC - SC Single Mode - Plug-in Module

Description:

Cable, Serial - Serial Connection

Description:

The "Just Convert-It" Bridging Media Converter is an inexpensive, no frills way to extend the distance between connections with different speeds or duplex using fiber optic cable, while maintaining the same quality and reliability found on Transition's full-featured line of products.

Description:

Transition Networks' analog video media receiver, J/VD-RX-01, converts the optical signal back to an analog composite video signal. All conversion is performed in real time. Automatic gain control installed on Receiver maintains desired quality of video's contrast and brightness for extended distances. No field adjustments are necessary. Wide input range power supply allows for multiple choices of power source including camera power supply.

Description:

The "Just Convert-It" Bridging Media Converter is an inexpensive, no frills way to extend the distance between connections with different speeds or duplex using fiber optic cable, while maintaining the same quality and reliability found on Transition's full-featured line of products.

Description:

Connecter: 1 x RJ-45 10 Base-T

Description:

2 x RJ-45 10/100Base-TX Duplex - 1 x SC 100Base-FX - UTP/STP - Fiber

Description:

The T1/E1 Copper to Fiber Media Converter enables the deployment of fiber into campus or industrial environments. This deployment of fiber into these environments provides a cost-effective solution and allows for the standardization on fiber as a media type. This is especially significant in industrial environments where fiber is immune to electrostatic interference "noise".

Description:

2 x BNC T3/E3 - SC Single Mode - Slide In Module

Description:

Point System Slide-In-Module media converter is designed to be used in any of the Point System chassis. Each Point System Slide-In-Module media converter, regardless of protocol, can slide into the same chassis and provide managed media conversion services to suit a custom network application.

Description:

The TN-SFP-XX Small Form Factor Pluggables (SFP) transceivers are designed for bi-directional...

Description:

1310 nm - 1.25 Mbps Half / Full Duplex

Description:

Transition Networks designs and manufactures Conversion Technology products, specializing in media converters. These products help customers cost-effectively deploy fiber by reducing the costs of electronics as much as 40%. The company's products are designed to protect the investment made in network infrastructure while optimizing its performance capacity. The DS3-T3/E3 copper to fiber media converter will provide a solution for those users that desire to extend the point of presence of their DS3 or E3 connection or use it to connect remote locations via T3/E3.

Description:

Ethernet, Fast Ethernet Connection

Description:

PRODUCT FEATURES:Extend network distanceBridge legacy 10/100 devices to a Gigabit backboneAuto-negotiation (copper and fiber ports)Switch selectable speeds (UTP) when auto-negotiation is offAutoCrossLink pass throughRemote fault detectPause

Description:

10/100/1000BASE-T to 1000BASE-SX/LX 10/100/1000 media converter that converts the electrical signal of a 10/100/1000 Ethernet signal from copper to fiber. This solution will offer a low-cost integration option for network managers who want to migrate from 10/100 networks to Gigabit Ethernet. Gigabit only switches can now be connected to 10/100 networks without the need to upgrade the 10/100 side, allowing network managers to add new equipment gradually.

Description:

Data Transfer Rate: 115 Kbps - Coaxial To Fiber

Description:

Transition Networks offers networking connectivity solutions that make the conversion between disparate media types possible. The company designs and markets these media conversion technologies across a broad spectrum of networking protocols including Ethernet, Fast Ethernet, ATM, Gigabit and Token Ring. The company works alongside leading networking vendors to provide conversion technology solutions that offer the necessary adaptations without affecting the performance, nature or appearance of the network to the users or the network devices.

Description:

Integrate mixed cabling environments using either switched or shared Ethernet. This full-featured media converter makes the migration from copper to fiber easier than ever before. AutoCross technology eliminates an entire category of network troubleshooting by automatically matching crossed and uncrossed cables to the appropriate connection. The twisted pair port is instantaneously configured to the correct MDI or MDI-X configuration. Because most Ethernet technologies are unable to recognize downlink faults, a failed link may appear normal to network management; requiring unnecessary troubleshooting. LinkAlert monitors all physical uplink and downlink failures and enables all faults to be detected by network management.

Description:

100BASE-FX/OC-3

Description:

Stand-Alone Mini 10/100 Bridging - Media converter - 10Base-T, 100Base-FX, 100Base-TX - RJ-45 - SC multi-mode - external - up to 1 miles - 1300 nm

Description:

The TN-SFP-XX Small Form Factor Pluggables (SFP) transceivers are designed for bi-directional serial optical data communications such as Gigabit Ethernet or Fiber Channel and speeds up to 1.25Gbps. The device is designed for use in Switches and routers compatible with Small Form Factor Pluggable Multi-Sourcing Agreement (MSA).

Description:

10Base-T, 100Base-FX, 100Base-TX - RJ-45 - ST multi-mode - external - up to 1 miles - 1310 nm

Description:

The Transition Networks small form factor pluggable (SFP) tranceiver modules are designed to install in any SFP port allowing for 1000Base-T, 1000Base-SX or 1000Base-LX interfaces to the network through the SFP connector. The tranceivers are Cisco compatible and are designed for bidirectional serial-optical data communication such as Gigabit Ethernet or fiber channel at speeds up to 1.25 Gbps.

Description:

The "Just Convert-It" Bridging Media Converter is an inexpensive, no frills way to extend the distance between connections with different speeds or duplex using fiber optic cable, while maintaining the same quality and reliability found on Transition's full-featured line of products.

Description:

The Transition Networks small form factor pluggable (SFP) tranceiver modules are designed to install in any SFP port allowing for 1000Base-T, 1000Base-SX or 1000Base-LX interfaces to the network through the SFP connector. The tranceivers are Cisco compatible and are designed for bidirectional serial-optical data communication such as Gigabit Ethernet or fiber channel at speeds up to 1.25 Gbps.

Description:

Transition Networks SSETF10xx-205 series Ethernet and Fast Ethernet Media Converters connect 10Base-TX or 100Base-TX shielded or unshielded twisted-pair copper cable to 10Base-SX or 100Base-SX fiber-optic cable.

Description:

TRANSITION Networks CFETF10xx-205 series Fast Ethernet media converters, designed to be installed in a PointSystem Media Conversion Center, connect 100BASE-TX shielded or unshielded twisted-pair copper cable to 100BASE-FX multimode or singlemode fiber-optic cable. CFETF1013-205 provides an RJ-45 twisted-pair copper 100BASE-TX connector and an RX (receive) and TX (transmit) MM-SC 100BASE-FX connector to multimode 1300nm fiber-optic cable.